View AGM6424B_538568.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

AZ DISPLAYS, INC.
COMPLETE LCD SOLUTIONS
SPECIFICATIONS FOR LIQUID CRYSTAL DISPLAY
PART NUMBER: DATE:
AGM6424B JANUARY 21, 2003
Page 1 of 14
AGM6424B
1. LCD Module
1.1 Main Data
No. Item Contents 173.0(W) x 73.0(H) x x 7.0(D) Unit mm mm dots mm mm (1) Module size (2) Viewing area (3) Dot Number (4) Dot Size (5) Dot pitch (6) LCD type 640
156.0 (W)
60.0 (H) x 240 (H)
x 3 (R.G.B) (W) 0.065(W) 0.08(W) x x
0.225(H) 0.24(H)
Color-STN (Negative type) (30) 1/244 6 o clock +0 ~ +50
C C pcs g
(7) Contrast ratio (8) Duty (9) Viewing direction (10) Operating temperature (11) Storage temperature (12) Backlight (13) Power Supply Voltage (14) Weight
-20 ~ +70 Cold Cathode Fluorescent Lamp (CCFL) x 1 3.3V (120)
Page 2 of 14
AGM6424B
1.2 Interface Pin Connection
CN1 : 52893-2090(MOLEX) / Suitable FPC : Pitch 0.5mm, width 10.5mm Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Signal FLM V SS CL1 VSS CL2 VSS DISP VDD VCON V SS D0 D1 D2 D3 V SS D4 D5 D6 D7 V SS Scan GND Input data latch signal GND Data shift clock GND Display control signal H:ON , L:OFF Logic supply voltage Contrast GND Display data Display data Display data Display data GND Display data Display data Display data Display data GND adjust voltage start-up signal Pin Function
CN2 : BHSR-02VS-1 (JST) / Suitable connector : SM02B-BHSS-1-TB (JST) Pin No. 1 2 Signal H.V GND Pin Function Power supply voltage for CFL CFL GND
Page 3 of 14
AGM6424B
2. Block Diagram
CN1
FLM CL1 CL2 DISP
D0~D7 Y1
Column Driving Circuit
Y1920
Row Driving Circuit
X1
COLOR
X240
LCD
PANEL
640 RGB x 240 DOTS
VDD VSS VCON
Power
Supply Circuit
CN2 CFL H.V GND
Page 4 of 14
AGM6424B
3. Maximum Ratings
3.1 Electrical Absolute Maximum Ratings. (VSS=0V) Item Symbol Min. Max. Unit Power supply for Logic VDD-VSS -0.3 7.0 V Input voltage (Note 1) VI -0.3 VDD+0.3 V Note 1. FLM,CL1,CL2,DISP,D0~D7. Note 2. Ta=25 C Note 3. Please be sure users are grounded when handling the LCD module.
3.2 Environmental Absolute Maximum Ratings Storage Item MIN. MAX. Ambient Temperature -20 C 70 C Humidity Note 4
Operating MIN. MAX. 0C 50 C Note 4
Remark Note1,2,3 No Condensation
Note 1. Ta at -20 C --------< 48hours, at 70 C --------< 120 hours. Note 2. Background color changes slightly depending on ambient temperature. This phenomenon is reversible. Note 3. When LCM is operated at 0 C, the lifetime of the CFL will be reduced. The response time at 0 C will increase.
Note 4. Ta<=50 C : 85%RH MAX. Ta> 50 C : Absolute humidity must be lower than the humidity of 85% RH at 50 C.
Page 5 of 14
AGM6424B
4. Electrical Characteristics
4.1 Electrical Characteristics of LCD Item Symbol Power Supply for Logic VDD Contrast adjust voltage Input Signal Voltage Note (2) Power supply current Note (3) Frame Frequency Note (4) VCON VIH VIL IDD fFLM Condition Ta= 5 C Note(1) Ta=25 C Ta=40 C H Level L Level VDD=3.3V (60) MIN. 3.0 (0.8) Typ. 3.3 (1.8) 0.8VDD 0 (40) (75) (90) (2.8) VDD 0.2VDD Max. 3.6 Unit V V V mA Hz
Note (1) The value is specified as the voltage at which the optimum contrast is obtained. Note (2) FLM,CL1,CL2,DISP,D0~D7 Note (3) fFLM=75Hz,Ta=25 C,Display pattern is Black/White cross pattern as below. RGB RGB
Note (4) No flicker or ripple phenomenon experienced on the display.
4.2 Electrical Characteristics of Backlight Item Symbol Min. Typ. Max. Unit Remark Starting Voltage VS (1000) Vrms Ta=5 C Lamp Voltage VL (490) Vrms Ta=25 C Frequency 40 60 80 KHz Ta=25 C fL Lamp Current IL (3.0) (3.5) (4.0) mArms Ta=25 C Note (1) Starting voltage is higher when the LCM operates at lower temperatures. Note (2) Average lifetime of CFL will be decreased when LCM is operated at lower temperatures. Note (3) CFL lifetime : 10000 hours Min. at I L=3.5mA, Ta=25 C
Page 6 of 14
AGM6424B
5. Optical Characteristics
5.1 Optical Characteristics of LCD Condition X axis Viewing Angle Range O 1,O 2 CR> 2 Y axis O =0 Contrast Ratio CR Response Time Rise Fall R G B W tr tf x y x y x y x y O O =0 , =0 O =0 ,O=0 O =0 , =0 O Item Symbol Min. 60 35 TBD (0.44) (0.30) (0.28) (0.44) (0.15) (0.16) (0.27) (0.30) Typ. (30) (340) (110) (0.49) (0.35) (0.33) (0.49) (0.20) (0.21) (0.32) (0.35) Ta= 25 C.(Backlight On) Max. Unit Remark Deg. Note 1,2 Note 3,4 ms Note 5 ms (0.54) (0.40) (0.38) (0.54) (0.25) (0.26) (0.37) (0.40) -
Color Tone (CIE Coordinate)
Note 1.
Definition of O and O O2 O1
Eye from (O, O1)
Note 2.
Definition of Viewing angle O 1 and O 2 CR
Eye from ( O , O2)
Y(O =180 )
X
X
2.0 O1<0 O
Y( O =0 )
O1
O2
CR vs Viewing and O
Page 7 of 14
AGM6424B
Note 3.
CR=
Definition of Contrast Ratio CR
Brightness at selected dot (B1) Brightness at non-selected dot (B2)
B1 B1 Brightness Sensor B2 Back light B2 Sensor : BM-7 Aperture : 1 Distance : 50 cm Operation voltage Note 4. Definition of CR and V
OP
CR
VOP
Operation Voltage
Note 5.
Definition of optical response time
Non-selected state
Selected state
Non-selected state
Brightness
100%
90%
tr Rise time
tf Fall time
10%
Page 8 of 14
AGM6424B
5.2 Optical Characteristics of Backlight Item Min, Brightness Brightness Uniformity -
Typ. (150) -
Max. +/-30
Unit cd/m2 %
Remark Note 1,2,3 Note 2,3,4
Note 1. Measurement Condition: Display data should be all ON (D0~D7=HIGH). VDD=3.3V,IL=3.5mArms,VCON should be adjusted at the optimum voltage
Note 2. Measured on the following 5 points of the display. DOTS Y=360 Y=960 Y=1560 Active area
X=60 DOTS X=120 X=180
P1 P4
P3
P2 P5
Note 3. The brightness shall be the average of P1~P5 points. Note 4. Definition of the brightness Uniformity Max brightness or Min brightness Average brightness Average brightness x100%
Page 9 of 14
AGM6424B
6. Interface Timing Chart
6.1 Timing Chart
CL1
(240+n)xT
FLM
D0~D7
X1
X2
X239 X240
Invalid data
CL1
T
CL2
X1 X2 B634 R635 G635 B635 R636 G636 B636 R637 G637 B637 R638 G638 B638 R639 G639 B639
D7 D6 D5 D4 D3 D2 D1 D0
R0 G0 B0 R1 G1 B1 R2 G2
B2 R3 G3 B3 R4 G4 B4 R5
G5 B5 R6 G6 B6 R7 G7 B7
Page 10 of 14
AGM6424B
6.2. Electrical Characteristics (VDD=3.0~4.5V ,VLCD= +10.0~ +42.0V, Ta= 0 C~40 C) Item Symbol Min. Typ. Max. Unit Shift clock period tWCK 66 ns Shift clock H pulse wide tWCKH 23 ns Shift clock L pulse wide tWCKL 23 ns Data setup time tDS ns 10 25 ns Data hold time tDH Latch pulse H pulse wide tWLPH 30 ns Shift clock rise to latch pulse rise time tLD 10 ns Shift clock fall to latch pulse fall time tSL 30 ns Latch pulse rise to shift clock rise time tLS 30 ns Latch pulse fall to shift clock fall time tLH 30 ns Enable setup time tTS 12 ns Input signal rise time tR 50 ns Input signal fall time tF 50 ns Output delay tD 44 ns FLM setup time tFS 30 ns FLM hold time tFH 50 ns
tWLPH
VIH
CL1
VIL
tLD tLS
CL2
tSL
tLH tWCKH tWCKL
VIH VIL
tR
tF tWCK tDS
VIH VIL
tDH
D0~D7
LAST DATA
Horizontal retrace period
TOP DATA
CL1
VIH VIL
tDS
CL2
tDH
1
2
..
20
tFS
FLM
tFH
Page 11 of 14
AGM6424B
6.3 Power Supply and Signal Sequence Do not apply DC voltage to the LCD panel because this induces an electrochemical reaction and reduces its lifetime. Please follow the power supply ON/OFF sequence below to prevent DC driving of the LCD or latch-up of the LSIs.
tDLD tDLD
VDD
tCH 0.8x VDD 0.8x VDD tCH
CL1
tDLCr tDLCf
VLCD
tDLCs 0.8x VDD
tDLCs 0.8x VDD 0.2x VDD tLDH
DISPOFF
tLDH tDOr
0.2x VDD
tDOf tVH
POWER ON
POWER OFF
SYMBOL tDLD tCH tLDH tDOr tDOf tDLCr tDLCf tDLCs tVH
MIN. 200 0 20 0 0 20 200
MAX. 100 100 -
UNIT ms ms ms ns ns ms ms ms ms
COMMENT
Note 1. Follow the timing sequence as shown above, since an improper sequence may cause permanent damage to the LCD panel. Note 2. Please use the DISPOFF function to turn the display off.
Page 12 of 14
AGM6424B
6.4 Input Data Allocation Table DDDDD Data Signal 76543 Y 1 X 1 2 3 4 5 6 7 8 9 10 | | | 238 239 240 R : RED G : GREEN B : BLUE R R R R R R R R R R | | | R R R G G G G G G G G G G | | | G G G B B B B B B B B B B | | | B B B R R R R R R R R R R | | | R R R G G G G G G G G G G | | | G G G 2 3 4 5
D 2 6 B B B B B B B B B B | | | B B B
D 1 7 R R R R R R R R R R | | | R R R
D 0 8 G G G G G G G G G G | | | G G G
D 7 9 B B B B B B B B B B | | | B B B
D 6
D 5
D 4 -------
10 11 12 R R R R R R R R R R | | | R R R G G G G G G G G G G | | | G G G B B B B B B B B B B | | | B B B
D 4 1 9 1 6 G G G G G G G G G G | | | G G G
D 3 1 9 1 7 B B B B B B B B B B | | | B B B
D 2 1 9 1 8 R R R R R R R R R R | | | R R R
D 1 1 9 1 9 G G G G G G G G G G | | | G G G
D 0 1 9 2 0 B B B B B B B B B B | | | B B B
6.5 Power supply for LCM
R1 +3.3V C1 + VR R2 Vcon
CFL VCFL
LCM
VDD
VSS
C2 + +3.3V -
VSS
Page 13 of 14
173.0 12.3 8.7 CN1
Inserting Direction
(105.0) 3.1
157.6 +/- 0.3 (156.0) 153.585 +/- 0.1
7.0
0.08 0.065
CN2 Bezel Opening Area Active Area 57.585 +/- 0.1 61.6 +/- 0.3 (60.0)
0.24 0.225
1
(39.5) 73.0
20
(20.05) 2.7
RGB
(4.8)
Active Area Center
Viewing Dirrction
(91.1)
CN1 : 52893-2090(MOLEX) CN2 : BHSR-02VS-1 (JST) Note 1 : All dimensional tolerance unless otherwise specified+/-0.5 Note 2 : Scale : NTS , Unit : mm
This datasheet has been download from: www..com Datasheets for electronics components.

▲Up To Search▲

Price & Availability of AGM6424B

	To Download AGM6424B Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .